Datenblatt für TC2030-IDC Drawing* von Tag-Connect LLC

.046 "
1.168 mm
.061 "
1.549 mm
1
2
5
6ALLOW A .061 X .046
SQUARE AREA OF
CLEARANCE FOR
EACH FOOT
PCB BOTTOM VIEW
.040 "
1.016 mm
B
.100 "
2.540 mm
.050 "
1.270 mm
.050 "
1.270 mm
.125 "
3.175 mm
.200 "
5.080 mm
.025
.635 mm
/NS
n.0935 "`.0030 n2.375 mm`.076
n.039 "`.003
n.991 mm`.076
n.031 "`.003
n.787 mm`.076
NON-PLATED
THRU HOLE
LEG LATCH HOLES
NON-PLATED
THRU HOLE
ALIGNMENT PIN HOLES
CONDUCTIVE
CONTACT PADS
NO SOLDER PASTE
1
2
5
6
www.TAG-CONNECT.com
Notes:
1. Allow clearance for finger squeeze access
from the two sides shown.
2. No tracks or vias in the shaded "KEEP OUT" AREA.
3. No other track or signal within
.02" of any contact pad.
4. Do not allow solder paste on the
contact pads It is essential to
eliminate any hole in the solder
paste-mask (solder stencil) layer.
If this is not possible make the
contact pads thru-hole with a
finished hole size of .008" or less.
5. Leg and alignment holes may be
plated and used as vias but ensure
minimum finished hole size meets
specified tolerances.
6. To prevent purchasing confusion,
please specify DNL in your BOM.
7. If using a proto-board fab that
plates all through holes, make
sure all holes are defined as
plated in the footprint.
ZONE
DWG NO.
SIZE
A
FSCM NO.
REV
SCALE
SHEET 1 Of 3
REV
12/05/19
MS
FOOTPRINT FOR TC2030-IDC PLUG-OF-NAILS(TM) CABLE
TC2030-IDC-FP
FOOTPRINT FOR
TC2030-IDC-FP
Allow finger access from this side
Allow finger access from this side
"KEEP OUT" AREA
"
@fifl @fllfl U9; L7'
.240 "
6.096 mm
1.15 "
29.21 mm
.446 "
11.328 mm
.131 "
3.327 mm
.750 "
19.05 mm
.39 "
9.906 mm
.078 "
1.9812 mm
.335 "
9.271 mm
1
2
5
6
.2935 "
7.4549
.300 "
7.62 mm
PCB
.2935 "
7.4549
.088 "
2.2352 mm
.050 "
1.27 mm
.078 "
1.9812 mm
A
D
Detail D
2
1 5
6
ZONE
SIZE
DWG NO.
SCALE
A
FSCM NO.
A
REV
SHEET 2 Of 3
MS
TC2030-IDC PLUG-OF-NAILS(TM) CABLE
TC2030-IDC
TC2030-IDC
5/17/11
B
END VIEW
www.TAG-CONNECT.com
Tag Connect inserted
into PCB for programming /
debugging
NOTE:
Dimensions subject to change
END VIEW
PART NUMBER
A
IN
.5
MM
TC2030-IDC
TC2030-IDC-10
8.8
10
225
265
TAG 6 PIN
IDC 6pin
1 1
2 2
3 3
4 4
5 5
6 6
A
Detail A
Vias between
contact pads
B
Detail B
Traces less than .02"
away from contact pad
or in "KEEP OUT" area
C
Detail C
Do not deposit solder paste
on contact pads. View Solder
Paste Mask (Solder Stencil)
layer in pad-stack and eliminate
any hole.
Layout Problems to Avoid
Large components
blocking finger access to
the Tag-Connect leg clips